What is the process for planting a tree?

Purchasing a tree is a lifelong investment. How well this investment grows depends on the type of tree selected, the planting location, the care provided during planting, and the follow-up care after planting. Please be sure to consult with an ISA Certified Arborist before picking out any tree and planting it. The most important step is tree selection and to pick the correct tree for your local environment. We have a video about selecting a tree here: What to Consider When Picking a Tree.

When to Plant

Ideally, trees are planted during the dormant season — in the fall after leaf drop or in early spring before bud break. Weather conditions are cool and allow plants to establish roots in the new location before spring rains and summer heat stimulate new top growth. Healthy balled and burlapped or container trees, however, can be planted throughout the growing season if given appropriate care. In tropical and subtropical climates where trees grow year round, any time is a good time to plant a tree, provided that sufficient water is available.

Planting: How to plant a tree.

Balled and burlapped trees lose a significant portion of their root system when dug at the nursery. As a result, trees commonly exhibit what is known as “transplant shock.” Transplant shock is a state of slowed growth and reduced vitality following transplanting. Container trees may also experience transplant shock, particularly if they have circling or kinked roots that must be cut. Proper site preparation, careful handling to prevent further root damage, and good follow-up care reduces transplant shock and promotes faster recovery.

Carefully follow the nine simple steps below to help your tree establish quickly in its new location. Note: Before you begin planting your tree, be sure you have located all underground utilities prior to digging.

Call Diggers Hotline before digging

 

1. Identify the trunk flare. The trunk flare is where the trunk expands at the base of the tree. This point should be partially visible after the tree has been planted. Remove excess soil from the top of the root ball prior to planting if the root flare is not visible.

2. Dig a shallow, broad planting hole. Holes should be 2 to 3 times wider than the root ball, but only as deep as the root ball. Digging a broad planting pit breaks up the surrounding soil and provides newly emerging tree roots room to expand. (Loosen Up the ball and roots before planting.)

3. Remove the containers or cut away the wire basket. Inspect container tree root balls for circling roots. Straighten, cut, or remove them. Expose the trunk flare, if necessary.

4. Place the tree at the proper height. Take care to dig the hole to the proper depth — and no more. The majority of a tree’s roots develop in the top 12 inches (30 cm) of soil. If the tree is planted too deep, new roots will have difficulty developing because of a lack of oxygen. In poorly drained or heavily clay soils, trees can be planted with the base of the trunk flare 2 to 3 inches (5 to 7.5 cm) above grade. When placing the tree in the hole, lift it by the root ball, not the trunk.

5. Straighten the tree in the hole. Before backfilling, have someone view the tree from several directions to confirm it is straight. Once planted, it is difficult to reposition the tree, so make sure its as best as you can before filling in.

6. Fill the hole gently, but firmly. Note: No Not Pack soil around the base of the root ball to stabilize it. If the root ball is wrapped, carefully cut and remove any fabric, plastic, string, and/or wire from around the trunk and root ball to prevent girdling and to facilitate root growth. Fill the remainder of the hole keeping it not packed down. To help reduce air pockets, watering periodically while backfilling can help. Avoid fertilization at the time of planting.

7. Stake the tree in 3 directions to help stabilize the tree. (Reminder – packing the soil down is not the way to stabilize the tree). Compacted soil is bad for trees, so do not pack it down when backfilling, very important you do this and allow the tree to lean for a bit while you stake. Stakes may also offer protection against lawn mower damage and vandalism. 3 stakes used in conjunction with a wide, flexible tie material on the lower half of the tree will hold the tree upright and minimize injury to the trunk, yet still allow movement. Remove support staking and ties after the first year of growth.

8. Mulch the base of the tree out as far as the drip line. Mulch is organic matter spread around the base of a tree to hold moisture, moderate soil temperature extremes, and reduce grass and weed competition. Common mulches include leaf litter, pine straw, shredded bark, peat moss, or composted wood chips. A 2- to 4-inch (5- to 10-cm) layer is ideal. More than 4 inches (10 cm) may cause a problem with oxygen and moisture levels. Piling mulch right up against the trunk of a tree may cause decay of the living bark. A mulch area, 1 to 2 inches (2.5 to 5 cm) wide at the base of the tree, reduces moist bark conditions and prevents decay.

9. Provide follow-up care. Keep the soil moist, but not waterlogged. Water trees at least once a week, barring rain, and more frequently during hot, windy weather. When the soil is dry below the surface of the mulch, it is time to water. Continue until mid-fall, tapering off as lower temperatures require less-frequent watering.

Other follow-up care may include minor pruning of branches damaged during the planting process. Prune sparingly after planting and delay necessary corrective pruning until a full season of growth in the new location has occurred.

Completing these nine simple steps will maximize the likelihood that your new tree will grow and thrive in its new home. When questions arise regarding your tree, be sure to consult your local ISA Certified Arborist at Capital City Tree Experts.